WWW.NOLINMILLING.COM · SALES@NOLINMILLING.COM
2018
18
(See punch pattern and
bolting information p 45)
Screw conveyor flanges p 21.
Custom flanges available.
Flat
Angle
Size
Flange
Iron
4"
1" x 3/16"
$22.90
$26.90
6"
1-1/4" x 3/16"
22.90
26.90
8"
1-1/4" x 3/16"
23.90
27.90
10"
1-1/4" x 3/16"
24.90
28.90
12"
1-1/2" x 3/16"
27.90
31.90
14"
1-1/2" x 3/16"
33.90
37.90
16"
1-1/2" x 3/16"
37.90
41.90
18"
1-1/2" x 3/16"
43.90
47.90
20"
1-1/2" x 3/16"
46.90
49.90
22"
1-1/2" x 3/16"
56.90
59.90
24"
1-1/2" x 3/16"
62.90
66.90
30"
2" x 3/16"
99.00
119.00
36"
2" x 3/16"
119.00
129.00
SQUARE FLANGES, PUNCHED
VERTICAL DROP FLOW RETARDERS
Special baffle design creates a moving pile at most flow rates, thus retarding
material speed. Units should be installed on ten foot intervals. 1/2" baffles.
AR steel on wear points. For round spouts use inlet and square to round.
Use one 10 foot length of square spout between units.
7 Ga Construction
1/4" Construction
Size
with 7 Ga AR liner
with 1/4" AR liner
6", 8"
$399.00
$529.00
10", 12"
599.00
779.00
14", 16"
789.00
1,029.00
18", 20"
1,239.00
1,619.00
22", 24"
1,819.00
2,349.00
VERTICAL DROP CUSHION TURNOUT 45
° ELBOW
Used when a spout comes straight down. Unit turns out 45° and has 1/2"
thick internal baffles to reduce grain velocity and form a moving pile at
point of impact. 1/2" baffles. AR steel liner on bottom. Square in and
square out. For round spouts, use inlet and square to round.
Z 45° SQUARE DEAD STOP WITH RUBBER CUSHION
Square in and square out with 1/4" black rubber cushion on back end plate at
approximately 40 degrees. Baffles are located below the angle of projection
allowing a pile to form on rubber cushion. Rubber on back end plate cushions
and slows material flow, thus forming pile. Better for varied flow rates.
7 Ga Construction
1/4" Construction
Size
with 7 Ga AR liner
with 1/4" AR liner
6", 8"
$399.00
$529.00
10", 12"
539.00
699.00
14", 16"
749.00
979.00
18", 20"
1,029.00
1,339.00
22", 24"
1,569.00
2,029.00
Size
7 Ga
1/4"
6", 8"
$399.00
$529.00
10", 12"
539.00
699.00
14", 16"
749.00
979.00
18", 20"
1,029.00
1,339.00
22", 24"
1,569.00
2,029.00
6"
$369.00 $429.00 $499.00
8"
369.00
429.00
499.00
10"
379.00
449.00
549.00
12"
499.00
629.00
769.00
14"
569.00
689.00
839.00
16"
869.00 1,049.00
18"
949.00 1,169.00
20"
1,099.00 1,349.00
24"
1,539.00 1,849.00
Size 10 Ga 7 Ga 1/4''
ADJUSTABLE SPOUT END, SQUARE INLET
Use with Square Spout. Preferred for Corn, Soybeans, & Feed Pellets.
Same features as Original Style Adjustable Spout Ends.
AR and Tile Liner Add-ons p 12.
HEAVY DUTY HINGE
Size Price
Size
Price
8"
$479.00
18"
$599.00
10"
499.00
20"
629.00
12"
529.00
24"
819.00
14"
549.00
30" 1,189.00
16"
579.00
OVERFLOW WITH INTERNAL 45 SLIDE GATE
8"
$749.00
$939.00
10"
789.00
979.00
12"
899.00
1,149.00
14"
1,089.00
1,399.00
16"
1,469.00
1,839.00
OVERFLOW WITH AIR SLIDE GATE
This overflow allows closing off vertical
drop without having material collect in
bottom of overflow.
SQUARE HINGE FOR LOAD-OUT SPOUT
Size
Price
8" . . . . . . . . .$139.00
10" . . . . . . . . . .169.00
12" . . . . . . . . . .189.00
14" . . . . . . . . . .199.00
16" . . . . . . . . . .239.00
18" . . . . . . . . . .279.00
SQUARE TURNDOWN FOR LOAD-OUT SPOUT
SQUARE EXPANSION JOINTS
10 ga. Lined
Size
7 Ga
with 7 Ga AR
8" $419.00
$729.00
10"
479.00
779.00
12"
549.00
869.00
14"
629.00
929.00
16"
729.00
999.00
18"
819.00
1,229.00
20"
929.00
1,319.00
24" 1,199.00
1,699.00
Size
Price
8", 10" . . . . . . $2,739.00
12", 14" . . . . . . . 2,819.00
16", 18", 20" . . . . 3,129.00
22", 24" . . . . . . . . 3,439.00
Constructed with 2" shaft pin, 1/2" plate housing sides, 12" long.
Spouting beyond hinge should be limited to 10 foot or less including
turndown.
Gate blocks any trickling flow to overflow side. When material backs up
into overflow, a high level switch is tripped and air gate will open allowing
material to overflow. The air gate has latching relay and will stay open
until reset. Square in and square out. 7 gauge carbon steel construction.
Equipped with totally enclosed electrical solenoid.
Size 10 Ga 7 Ga
Size
10 Ga
7 Ga
6 & 8"
$139.00
$189.00
10"
169.00
219.00
12"
189.00
249.00
14"
199.00
279.00
16"
239.00
329.00
18"
279.00
379.00
20"
369.00
489.00
Installed length
29" to 30". Spout
should be supported
with A-frame above
Expansion Joint.
Unflanged
Discharge
Flanged
Discharge
Adjusts from
90º to 35º
0